A burst pipe tells you where the system failed. It doesn't tell you why.
That distinction is worth money, because pipes rarely fail at random. Something acted on that section — pressure, temperature, water chemistry, movement, or a decision made when it was installed — and whatever it was is still acting on the rest of the run. Replace the failed length without identifying the cause and you've bought time, not a solution. The second failure usually arrives a few feet from the first.
Which is why the useful question on any pipe repair isn't "can you fix it." It's "why did this happen here, and what else is on the same trajectory."
PrimeFlow Plumbing Services repairs pipes across Unadilla and tells you what caused the failure.
Tap to call — or find your likely cause below.
The most common cause nobody checks, and the only one you can measure yourself in five minutes. Excessive pressure stresses every joint, fitting, valve, and appliance connection in the property continuously. The tell: banging pipes, taps that spray rather than flow, running toilets, appliance inlet valves failing early, and a relief valve on the water heater that discharges periodically. It's covered in detail in the next section, because it's fixable.
Water expands as it freezes and splits the pipe. The failure usually appears on thawing, not on freezing. The tell: the timing — a burst during or immediately after a cold snap, most often in an unheated space: crawlspace, attic, garage, exterior wall, or an unheated outbuilding.
Water chemistry acts on pipe walls over decades. Some water is naturally aggressive; softened water, high mineral content, and low pH all accelerate it. The tell: discoloured water, staining at fixtures, gradually declining pressure across the whole property, and pinhole leaks appearing in more than one place — the signature that this is systemic rather than local.
Two different metals joined directly, with water as the electrolyte, corrode at the junction. The tell: failure exactly at a transition point — copper meeting galvanised steel is the classic — with heavy build-up right at the joint and sound pipe on either side. Frequently the legacy of a partial repipe done without a dielectric fitting.
Pipes need to be supported and allowed to expand. Unsupported runs sag and stress their joints; pipes clamped rigidly with no allowance for thermal movement stress themselves every time hot water passes through. The tell: ticking or knocking as hot water runs, visible sag between supports, and failures at fittings rather than mid-pipe.
Under-supported runs, over-tightened fittings, joints made poorly, incompatible materials, undersized pipe, or work never inspected. The tell: failure in a section that's visibly newer than the rest of the property, or clustered around a past renovation.
A nail or screw driven through a pipe during other work, a pipe crushed behind a fixture, ground movement acting on a buried line, or vehicle loading over a service line. The tell: a failure that coincides with work done recently, or one in a buried line with no other explanation.
We'll tell you which of these you're looking at. For four of the seven, the fix is a different job from the pipe repair — and knowing that before the wall closes is what stops the second call.
Water pressure is the most common contributor to premature pipe and fitting failure, and it's the easiest to check.
A threaded pressure gauge costs very little and screws onto an outside hose bib or a laundry tap. Attach it, open the tap fully, and read it with no water running elsewhere in the property.
Typical residential supply sits comfortably in the range of roughly 40 to 60 psi. Readings above about 80 psi are generally considered too high, and many jurisdictions treat that figure as the limit at which a pressure reducing valve is required. Some municipal supplies deliver considerably more than that at the meter.
High pressure doesn't feel like a problem. It feels like good water pressure. What it's doing is stressing every connection in the building continuously, shortening the life of flexible hoses, appliance inlet valves, cistern valves, and the water heater — while making a burst more likely at whatever section is already weakest.
The fix is a pressure reducing valve at the point of entry, set correctly. They also fail over time and drift out of adjustment, so a property that has one isn't automatically protected.
Thermal expansion is the related issue. In a closed system — one with a check valve, backflow preventer, or PRV at the meter — heated water expands with nowhere to go, spiking pressure every heating cycle. That's what an expansion tank exists to absorb, and its absence is a common finding when a relief valve keeps discharging.
Check yours before booking anything. If it's high, that's a conversation worth having in the same visit.
The number of failures matters more than the size of any one of them.
We'll give you both numbers — the repair and the repipe — and the reasoning. What we won't do is keep patching a system we can see is failing without telling you that's what's happening.
Pipes run inside walls, ceilings, and floors. Reaching them means opening them.
The failures are predictable, which makes them preventable.
We repair and replace pipework for restaurants, retail, offices, warehouses, and multi-unit residential buildings across Unadilla.
Commercial systems fail under different conditions — higher and more continuous demand, larger diameters, longer runs, and buildings frequently repurposed with modifications layered in over decades.
In multi-unit buildings, a failure in a shared riser affects residents with no connection to the cause, and isolating the affected section without shutting the whole building is usually the first problem to solve.
Downtime governs the planning. We define which areas need isolating and for how long before starting, and schedule around trading where a shutdown would otherwise close you.
You'll have the price before work begins.
PrimeFlow Plumbing Services proudly serves Unadilla, GA and the surrounding neighborhoods, repairing and replacing pipework in residential and commercial properties throughout the area. Unsure whether you're in range? Call and ask.
Because something acted on that section — pressure, freezing, corrosion, a dissimilar metal joint, movement, an installation defect, or physical damage. Identifying which is what stops the next one.
A threaded gauge on an outside hose bib or laundry tap, read with nothing else running. Typical supply sits around 40 to 60 psi; above roughly 80 psi is generally considered too high and usually calls for a pressure reducing valve.
No — it's a pattern. A second failure in a short period suggests something systemic rather than coincidence, and it's the right moment to price a repipe against continued repairs.
Small perforations caused by corrosion from inside the pipe, usually driven by water chemistry or velocity. Several in different places is the clearest sign the problem is the system rather than the section.
A repair clamp holds pressure temporarily. It isn't a permanent repair, and it shouldn't be relied on as one — particularly inside a wall where the next failure won't be visible.
First failure with a local cause: repair. Second failure in a short period: get both numbers. Third: repiping is usually already the cheaper path once you count the repairs still ahead of you.
For pipes inside walls, yes. We keep openings small and few, place them discreetly where possible, and patch to a ready-for-paint condition — with finishing usually separate, stated before we start.
Often high pressure, sometimes water hammer from fast-closing valves, sometimes poor support. All three are worth addressing, since all three stress the system continuously.
Water standing overnight in corroding pipe. If it clears after running and only affects the hot side, look at the water heater; if it affects both and the property is older, look at the pipework.
Shut off the main first, open the affected tap, and apply gentle indirect heat only. Never a flame or heat gun. If you can't locate the frozen section or it's inside a wall, call.
Yes, continuously — every joint, valve, flexible hose, and appliance connection in the property. It's the most common contributor to premature failure and the easiest to measure.
A single repair usually doesn't. Repiping a branch or a property generally does, and it's inspected work. We'll tell you what applies.
It's driven mainly by access and by whether you need a repair or a repipe. You'll have the price before work begins, along with the repipe figure if it's relevant.